Finding one reliable supplier for every cutting job is the fastest way to shorten lead times, cut landed cost, and remove quality risk from your supply chain. Oridawn is a diamond saw blade manufacturer with more than ten years in the industry. Through a network of audited partner factories, we also supply tungsten-carbide-tipped (TCT) and high-speed steel (HSS) saw blades held to the same strict standard — giving you a single point of contact for a complete, one-stop cutting solution, exported to more than 50 countries.
Most importers source diamond blades, TCT blades and HSS blades from three separate vendors, which means three minimum orders, three freight invoices and three sets of paperwork. Consolidating into one supplier delivers measurable savings:
· Lower landed cost — one consolidated container replaces three smaller, higher-per-unit shipments.
· Fewer vendors to audit — you qualify one factory network instead of managing three.
· One QC report — a single inspection standard and one accountable contact when something goes wrong.
· Consistent quality bar — every blade type, whether we make it in-house or source it, is held to the same tolerance and safety standards.
Diamond saw blades are our core product, and they are made in our own 33,333 m² facility in Ezhou, Hubei, with a marketing and export center in Wuhan. Founded in 2016, we have spent close to two decades refining segment formulation and welding processes — the two factors that decide how a blade cuts and how long it lasts.
Because we control production directly, we can hold the specifications that matter most in the field: diamond grit concentration, bond hardness matched to the material, segment height, and weld integrity. Every batch runs under an ISO 9001 quality management system with dimensional inspection and cutting testing before release.
Laser welding fuses the segment to the steel core with a full-depth, high-strength bond that tolerates dry-cutting heat. These blades are built for green concrete, cured concrete and rebar-reinforced concrete, on both hand-held saws and high-power walk-behind or table machines. If your market cuts concrete with embedded rebar, this is the range to start with.
High-frequency welding bonds the segment through a lower-temperature process, which is ideal where a cost-efficient blade is needed for general concrete, block and masonry without sacrificing consistency. This range offers a strong price-performance balance for high-volume distributors.
For natural stone and tile, the bond must be matched to a harder, denser material to avoid glazing and overheating. Our stone blades are formulated for clean, chip-free edges on marble, granite and porcelain, and are a natural add-on for any buyer already purchasing our concrete blades.
Explore the full range in our diamond saw blade catalog.
Tungsten-carbide-tipped saw blades handle materials a diamond blade is not designed for: solid wood, plywood, MDF, aluminum profiles and other non-ferrous metals. Rather than build a second production line outside our expertise, we partner with specialist TCT blade manufacturers that meet our quality bar, so you get professional-grade cutting without the trial-and-error of finding your own vendor.
· Woodworking blades produced to EN 847-1 safety and dimensional requirements.
· Carbide grade and tooth geometry specified per material — ripping, crosscut or aluminum cutting.
· Consistent runout, plate tension and balance for smooth, long-life cutting.
High-speed steel blades are the workhorse for cutting steel, stainless profiles and tougher metals where a carbide edge would chip. Our HSS blades come from the same audited partner network and are selected for hardness, tooth finish and concentricity, giving your customers a dependable blade for metal-cutting saws and tube-cutting applications.
"One-stop" only works if quality does not drop the moment a blade is not diamond. That is why we treat every partner factory as an extension of our own QC system:
1. Factory qualification — we audit production equipment, raw material sourcing and quality records before onboarding any partner.
2. Standard-aligned production — diamond blades to EN 13236:2019, woodworking TCT blades to EN 847-1, and ANSI B7.1 variants for North America.
3. Batch inspection — hardness, runout, plate tension and weld strength are checked on every production lot, not sampled at random.
4. Pre-shipment verification — we can arrange third-party inspection and provide test reports before your goods leave port.
For a distributor or wholesaler, the value is operational, not just promotional. Working with Oridawn you get:
· Mixed-container orders — combine diamond, TCT and HSS blades in one shipment to consolidate freight.
· One accountable contact — one email, one order, one invoice, one shipment and one QC report.
· OEM / ODM support — private-label branding and custom specifications across all three blade categories.
· Sample program — test before you commit, with inspection reports on request.
We do not ask you to take our word for it. Any serious buyer can:
· Request samples for field testing in your own market.
· Review our ISO 9001 certificate and dimensional inspection reports.
· Arrange third-party pre-shipment inspection.
· Audit the factory — ours or our partner factories — before placing a volume order.
Read more about who we are on our About Oridawn page, or see how we produce blades on the factory and manufacturing page.
Diamond saw blades are made in our own 33,333m² facility in Ezhou. TCT and HSS blades come from a network of audited partner factories held to the same ISO 9001 and dimensional standards we apply to our own production.
MOQ depends on blade type and specification, and mixed-container orders are welcome — so you can combine diamond, TCT and HSS blades in one shipment and consolidate freight.
Yes. We offer OEM branding and ODM development across all three blade categories, supported by our engineering team and partner factories.
Production is ISO 9001 certified; diamond blades are produced to EN 13236:2019, woodworking TCT blades to EN 847-1, with ANSI B7.1 variants available for North America.
Yes. We provide samples, inspection reports, and can arrange third-party inspection before shipment.
Stop juggling three vendors and three quality standards. Tell us what you cut, and we will recommend the right diamond, TCT and HSS blade specification for your market — with samples, test reports and a single point of contact.
